...

AD7366 数据手册DataSheet下载

by user

on
Category: Documents
2

views

Report

Comments

Transcript

AD7366 数据手册DataSheet下载
FEATURES
FUNCTIONAL BLOCK DIAGRAM
DCAP A
VDD
Dual 12-bit/14-bit, 2-channel ADC
True bipolar analog inputs
Programmable input ranges:
±10 V, ±5 V, 0 V to 10 V
±12 V with 3 V external reference
Throughput rate: 1 MSPS
Simultaneous conversion with read in less than 1 μs
High analog input impedance
Low current consumption:
8.3 mA typical in normal mode
320 nA typical in shutdown mode
AD7366
72 dB SNR at 50 kHz input frequency
12-bit no missing codes
AD7367
76 dB SNR at 50 kHz input frequency
14-bit no missing codes
Accurate on-chip reference: 2.5 V ± 0.2%
−40°C to +85°C operation
High speed serial interface
Compatible with SPI®, QSPI™, MICROWIRE™, and DSP
iCMOS® process technology
Available in a 24-lead TSSOP
DVCC
BUF
REF
AD7366/AD7367
VA1
MUX
12-/14-BIT
SUCCESSIVE
APPROXIMATION
ADC
T/H
OUTPUT
DRIVERS
DOUTA
VA2
SCLK
CNVST
CS
BUSY
ADDR
RANGE0
RANGE1
REFSEL
VDRIVE
CONTROL
LOGIC
VB1
MUX
VB2
T/H
12-/14-BIT
SUCCESSIVE
APPROXIMATION
ADC
OUTPUT
DRIVERS
DOUTB
AGND AGND
VSS
DCAP B
DGND
06703-001
BUF
Figure 1.
GENERAL DESCRIPTION
PRODUCT HIGHLIGHTS
The AD7366/AD7367 1 are dual 12-bit/14-bit, high speed, low
power, successive approximation analog-to-digital converters
(ADCs) that feature throughput rates up to 1 MSPS. The device
contains two ADCs, each preceded by a 2-channel multiplexer,
and a low noise, wide bandwidth track-and-hold amplifier.
1.
The AD7366/AD7367 are fabricated on the Analog Devices, Inc.,
industrial CMOS process (iCMOS 2), which is a technology
platform combining the advantages of low and high voltage
CMOS. The iCMOS process allows the AD7366/AD7367 to
accept high voltage bipolar signals in addition to reducing
power consumption and package size. The AD7366/AD7367
can accept true bipolar analog input signals in the ±10 V range,
±5 V range, and 0 V to 10 V range.
3.
The AD7366/AD7367 have an on-chip 2.5 V reference that
can be disabled to allow the use of an external reference.
If a 3 V reference is applied to the DCAPA and DCAPB pins, the
AD7366/AD7367 can accept a true bipolar ±12 V analog input.
Minimum ±12 V VDD and VSS supplies are required for the
±12 V input range.
AVCC
2.
The AD7366/AD7367 can accept true bipolar analog input
signals, as well as ±10 V, ±5 V, ±12 V (with external reference), and 0 V to 10 V unipolar signals.
Two complete ADC functions allow simultaneous sampling
and conversion of two channels.
1 MSPS serial interface: SPI-/QSPI-/DSP-/MICROWIREcompatible interface.
Table 1. Related Products
Device
AD7366
AD7366-5
AD7367
AD7367-5
1
2
Resolution
12-Bit
12-Bit
14-Bit
14-Bit
Throughput
Rate
1 MSPS
500 kSPS
1 MSPS
500 kSPS
Number of
Channels
Dual, 2-channel
Dual, 2-channel
Dual, 2-channel
Dual, 2-channel
Protected by U.S. Patent No. 6,731,232.
iCMOS Process Technology. For analog systems designers within
industrial/instrumentation equipment OEMs who need high performance
ICs at higher voltage levels, iCMOS is a technology platform that enables the
development of analog ICs capable of 30 V and operating at ±15 V supplies
while allowing dramatic reductions in power consumption and package size,
and increased ac and dc performance.
www.BDTIC.com/ADI/
TABLE OF CONTENTS
Features .............................................................................................. 1
Typical Connection Diagram ................................................... 18
Functional Block Diagram .............................................................. 1
Driver Amplifier Choice ........................................................... 19
General Description ......................................................................... 1
Reference ..................................................................................... 19
Product Highlights ........................................................................... 1
Modes of Operation ....................................................................... 20
Revision History ............................................................................... 2
Normal Mode .............................................................................. 20
Specifications..................................................................................... 3
Shutdown Mode ......................................................................... 21
Timing Specifications .................................................................. 7
Power-Up Times ......................................................................... 21
Absolute Maximum Ratings ............................................................ 8
Serial Interface ................................................................................ 22
ESD Caution .................................................................................. 8
Microprocessor Interfacing ........................................................... 24
Pin Configuration and Function Descriptions ............................. 9
AD7366/AD7367 to ADSP-218x.............................................. 24
Typical Performance Characteristics ........................................... 11
AD7366/AD7367 to ADSP-BF53x ........................................... 24
Terminology .................................................................................... 14
AD7366/AD7367 to TMS320VC5506 ..................................... 25
Theory of Operation ...................................................................... 16
AD7366/AD7367 to DSP563xx ................................................ 25
Circuit Information .................................................................... 16
Application Hints ........................................................................... 27
Converter Operation .................................................................. 16
Layout and Grounding .............................................................. 27
Analog Inputs .............................................................................. 16
Outline Dimensions ....................................................................... 28
Transfer Function ....................................................................... 17
Ordering Guide .......................................................................... 28
REVISION HISTORY
11/10—Rev. C to Rev. D
Changes to DOUTA and DOUTB Description in Table 6 ................. 9
Changes to Serial Interface Section .............................................. 22
Changes to Figure 27 ...................................................................... 23
10/10—Rev. B to Rev. C
Changes to DOUTA and DOUTB Description in Table 6 ................. 9
Changes to Serial Interface Section .............................................. 22
Changes to Figure 27 ...................................................................... 23
8/09—Rev. A to Rev. B
Changes to Table 2 ............................................................................ 4
Changes to Table 3 ............................................................................ 6
9/07—Rev. 0 to Rev. A
Changes to Title ............................................................................... 1
Changes to Specifications ................................................................ 3
Changes to Figure 5 ........................................................................ 11
Changes to Terminology Section.................................................. 14
Changes to Figure 20 ...................................................................... 18
Changes to Figure 28 ...................................................................... 23
Updated Outline Dimensions ....................................................... 28
Changes to Ordering Guide .......................................................... 28
5/07—Revision 0: Initial Version
www.BDTIC.com/ADI/
SPECIFICATIONS
AVCC = DVCC = 4.75 V to 5.25 V, VDD = 11.5 V to 16.5 V, VSS = −16.5 V to −11.5 V, VDRIVE = 2.7 V to 5.25 V, fS = 1.12 MSPS, fSCLK = 48 MHz,
VREF = 2.5 V internal/external, TA = −40°C to +85°C, unless otherwise noted.
Table 2. AD7366
Parameter
DYNAMIC PERFORMANCE
Signal-to-Noise Ratio (SNR) 1
Signal-to-Noise + Distortion Ratio (SINAD)1
Total Harmonic Distortion (THD)1
Spurious-Free Dynamic Range (SFDR)
Intermodulation Distortion (IMD)1
Second-Order Terms
Third-Order Terms
Channel-to-Channel Isolation1
SAMPLE AND HOLD
Aperture Delay 2
Aperture Jitter2
Aperture Delay Matching2
Full Power Bandwidth
DC ACCURACY
Resolution
Integral Nonlinearity (INL)1
Differential Nonlinearity (DNL)1
Positive Full-Scale Error1
Positive Full-Scale Error Match1
Zero Code Error1
Zero Code Error Match1
Negative Full-Scale Error1
Negative Full-Scale Error Match1
Min
Typ
70
70
72
71
−85
−87
Max
Unit
−78
−78
dB
dB
dB
dB
fa = 49 kHz, fb = 51 kHz
−88
−88
−90
dB
dB
dB
10
40
±100
35
8
12
ns
ps
ps
MHz
MHz
Bits
LSB
LSB
LSB
LSB
LSB
LSB
±0.5
±0.25
±1
±1
±1.5
±0.1
±1
±0.5
±7
±6
±0.5
±1
±1.5
±0.1
±3
±6
LSB
LSB
LSB
LSB
±1
±1
±1.5
±0.1
±7
±6
LSB
LSB
LSB
LSB
±10
±5
0 to 10
±1
V
V
V
µA
pF
pF
kΩ
MΩ
kΩ
MΩ
ANALOG INPUT
Input Voltage Ranges
DC Leakage Current
Input Capacitance
Input Impedance
Test Conditions/Comments
fIN = 50 kHz sine wave
@ 3 dB, ±10 V range
@ 0.1 dB, ±10 V range
Guaranteed no missed codes to 12 bits
±5 V and ±10 V analog input range
0 V to 10 V analog input range
Matching from ADC A to ADC B
Channel-to-channel matching for ADC A and
ADC B
±5 V and ±10 V analog input range
0 V to 10 V analog input range
Matching from ADC A to ADC B
Channel-to-channel matching for ADC A and
ADC B
±5 V and ±10 V analog input range
0 V to 10 V analog input range
Matching from ADC A to ADC B
Channel-to-channel matching for ADC A and
ADC B
Programmed via RANGE pins; see Table 8
±0.01
9
13
260
2.5
125
1.2
When in track, ±10 V range
When in track, ±5 V and 0 V to 10 V range
±10 V @ 1 MSPS
±10 V @ 100 kSPS
±5 V and 0 V to 10 V range @ 1 MSPS
±5 V and 0 V to 10 V range @ 100 kSPS
www.BDTIC.com/ADI/
Parameter
REFERENCE INPUT/OUTPUT
Reference Output Voltage 3
Long-Term Stability
Output Voltage Hysteresis1
Reference Input Voltage Range
DC Leakage Current
Input Capacitance
DCAPA, DCAPB Output Impedance
Reference Temperature Coefficient
VREF Noise
LOGIC INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN
Input Capacitance, CIN2
LOGIC OUTPUTS
Output High Voltage, VOH
Output Low Voltage, VOL
Floating State Leakage Current
Floating State Output Capacitance2
CONVERSION RATE
Conversion Time
Track/Hold Acquisition Time2
Throughput Rate
Min
Typ
Max
Unit
Test Conditions/Comments
2.495
2.5
150
50
2.505
V
ppm
ppm
V
µA
pF
pF
Ω
ppm/°C
µV rms
±0.2% max @ 25°C
1000 hours
2.5
±0.01
25
17
7
6
20
3.0
±1
25
0.7 × VDRIVE
±0.01
6
0.8
±1
V
V
µA
pF
0.4
±1
V
V
µA
pF
VDRIVE − 0.2
±0.01
8
1
2
3
VIN = 0 V or VDRIVE
ns
ns
MSPS
MSPS
5.25
+16.5
−11.5
5.25
V
V
V
V
370
40
1.5
550
60
2.25
µA
µA
mA
1.8
1.5
5
2.0
1.6
5.65
mA
mA
mA
VDD = +16.5 V
VSS = −16.5 V
VCC = 5.5 V
fS = 1.12 MSPS
VDD = +16.5 V
VSS = −16.5 V
VCC = 5.25 V, internal reference enabled
0.01
0.01
0.3
1
1
3
µA
µA
µA
VDD = +16.5 V
VSS = −16.5 V
VCC = 5.25 V
89.1
mW
48.75
mW
mW
µW
VDD = +16.5 V, VSS = −16.5 V, VCC = 5.25 V,
fS = 1.12 MSPS
±10 V input range, fS = 1.12 MSPS
±5 V and 0 V to 10 V input range, fS = 1.12 MSPS
VDD = +16.5 V, VSS = −16.5 V, VCC = 5.25 V
4.75
+11.5
−16.5
2.7
50
70
1.9
Shutdown Mode
Bandwidth = 3 kHz
610
140
1.12
1
POWER REQUIREMENTS
VCC
VDD
VSS
VDRIVE
Normal Mode (Static)
IDD
ISS
ICC
Normal Mode (Operational)
IDD
ISS
ICC
Shutdown Mode
IDD
ISS
ICC
Power Dissipation
Normal Mode (Operational)
External reference applied to Pin DCAPA/Pin DCAPB
±5 V and ±10 V analog input range
0 V to 10 V analog input range
Full-scale step input
4.75 V ≤ VDRIVE ≤ 5.25 V, fSCLK = 48 MHz
2.7 V ≤ VDRIVE < 4.75 V, fSCLK = 35 MHz
Digital inputs = 0 V or VDRIVE
See Table 7
See Table 7
See Table 7
See the Terminology section.
Sample tested during initial release to ensure compliance.
Refers to Pin DCAPA or Pin DCAPB specified for 25oC.
www.BDTIC.com/ADI/
AVCC = DVCC = 4.75 V to 5.25 V, VDD = 11.5 V to 16.5 V, VSS = −16.5 V to −11.5 V, VDRIVE = 2.7 V to 5.25 V, fS = 1 MSPS, fSCLK = 48 MHz,
VREF = 2.5 V internal/external, TA = −40°C to +85°C, unless otherwise noted.
Table 3. AD7367
Parameter
DYNAMIC PERFORMANCE
Signal-to-Noise Ratio (SNR) 1
Signal-to-Noise + Distortion Ratio (SINAD)1
Total Harmonic Distortion (THD)1
Spurious-Free Dynamic Range (SFDR)
Intermodulation Distortion (IMD)1
Second-Order Terms
Third-Order Terms
Channel-to-Channel Isolation1
SAMPLE AND HOLD
Aperture Delay 2
Aperture Jitter2
Aperture Delay Matching2
Full Power Bandwidth
DC ACCURACY
Resolution
Integral Nonlinearity (INL)1
Differential Nonlinearity (DNL)1
Positive Full-Scale Error1
Positive Full-Scale Error Match1
Zero Code Error1
Zero Code Error Match1
Negative Full-Scale Error1
Negative Full-Scale Error Match1
Min
Typ
74
73
76
75
−84
−87
Max
Unit
−78
−79
dB
dB
dB
dB
fa = 49 kHz, fb = 51 kHz
−91
−89
−90
dB
dB
dB
10
40
±100
35
8
14
ns
ps
ps
MHz
MHz
Bits
LSB
LSB
LSB
LSB
LSB
LSB
±2
±0.5
±4
±5
±3
±0.2
±3.5
±0.90
±20
±20
±1
±5
±3
±0.2
±10
±20
LSB
LSB
LSB
LSB
±4
±5
±3
±0.2
±20
±20
LSB
LSB
LSB
LSB
±10
±5
0 to 10
±1
V
V
V
µA
pF
pF
kΩ
MΩ
kΩ
MΩ
ANALOG INPUT
Input Voltage Ranges
DC Leakage Current
Input Capacitance
Input Impedance
Test Conditions/Comments
fIN = 50 kHz sine wave
@ 3 dB, ±10 V range
@ 0.1 dB, ±10 V range
Guaranteed no missed codes to 14 bits
±5 V and ±10 V analog input range
0 V to 10 V analog input range
Matching from ADC A to ADC B
Channel-to-channel matching for ADC A and
ADC B
±5 V and ±10 V analog input range
0 V to 10 V analog input range
Matching from ADC A to ADC B
Channel-to-channel matching for ADC A and
ADC B
±5 V and ±10 V analog input range
0 V to 10 V analog input range
Matching from ADC A to ADC B
Channel-to-channel matching for ADC A and
ADC B
Programmed via RANGE pins; see Table 8
±0.01
9
13
260
2.5
125
1.2
When in track, ±10 V range
When in track, ±5 V and 0 V to 10 V range
±10 V @ 1 MSPS
±10 V @ 100 kSPS
±5 V and 0 V to 10 V range @ 1 MSPS
±5 V and 0 V to 10 V range @ 100 kSPS
www.BDTIC.com/ADI/
Parameter
REFERENCE INPUT/OUTPUT
Reference Output Voltage 3
Long-Term Stability
Output Voltage Hysteresis1
Reference Input Voltage Range
DC Leakage Current
Input Capacitance
DCAPA, DCAPB Output Impedance
Reference Temperature Coefficient
VREF Noise
LOGIC INPUTS
Input High Voltage, VINH
Input Low Voltage, VINL
Input Current, IIN
Input Capacitance, CIN2
LOGIC OUTPUTS
Output High Voltage, VOH
Output Low Voltage, VOL
Floating State Leakage Current
Floating State Output Capacitance2
CONVERSION RATE
Conversion Time
Track/Hold Acquisition Time2
Throughput Rate
Min
Typ
Max
Unit
Test Conditions/Comments
2.495
2.5
150
50
2.505
V
ppm
ppm
V
µA
pF
pF
Ω
ppm/°C
µV rms
±0.2% max @ 25°C
1000 hours
2.5
±0.01
25
17
7
6
20
3.0
±1
25
0.7 × VDRIVE
±0.01
6
0.8
±1
V
V
µA
pF
0.4
±1
V
V
µA
pF
VDRIVE − 0.2
±0.01
8
VIN = 0 V or VDRIVE
ns
ns
MSPS
kSPS
5.25
+16.5
−11.5
5.25
V
V
V
V
370
40
1.5
550
60
2.25
µA
µA
mA
1.8
1.5
5
2.0
1.6
5.65
mA
mA
mA
VDD = +16.5 V
VSS = −16.5 V
VCC = 5.5 V
fS = 1 MSPS
VDD = +16.5 V
VSS = −16.5 V
VCC = 5.25 V, internal reference enabled
0.01
0.01
0.3
1
1
3
µA
µA
µA
VDD = +16.5 V
VSS = −16.5 V
VCC = 5.25 V
80.7
50
70
1.9
89.1
mW
mW
mW
µW
VDD = +16.5 V, VSS = −16.5 V, VCC = 5.25 V
±10 V input range, fS = 1 MSPS
±5 V and 0 V to 10 V input range, fS = 1 MSPS
VDD = +16.5 V, VSS = −16.5 V, VCC = 5.25 V
4.75
+11.5
−16.5
2.7
Shutdown Mode
Bandwidth = 3 kHz
680
140
1
900
POWER REQUIREMENTS
VCC
VDD
VSS
VDRIVE
Normal Mode (Static)
IDD
ISS
ICC
Normal Mode (Operational)
IDD
ISS
ICC
Shutdown Mode
IDD
ISS
ICC
Power Dissipation
Normal Mode (Operational)
External reference applied to Pin DCAPA/Pin DCAPB
±5 V and ±10 V analog input range
0 V to 10 V analog input range
48.75
Full-scale step input
4.75 V ≤ VDRIVE ≤ 5.25 V, fSCLK = 48 MHz
2.7 V ≤ VDRIVE < 4.75 V, fSCLK = 35 MHz
Digital inputs = 0 V or VDRIVE
See Table 7
See Table 7
See Table 7
1
See the Terminology section.
Sample tested during initial release to ensure compliance.
3
Refers to Pin DCAPA or Pin DCAPB specified for 25oC.
2
www.BDTIC.com/ADI/
TIMING SPECIFICATIONS
AVCC = DVCC = 4.75 V to 5.25 V, VDD = 11.5 V to 16.5 V, VSS = −16.5 V to −11.5 V, VDRIVE = 2.7 V to 5.25 V, TA = −40°C to +85°C,
unless otherwise noted. 1
Table 4.
Limit at TMIN , TMAX
2.7 V ≤ VDRIVE < 4.75 V 4.75 V ≤ VDRIVE ≤ 5.25 V
Unit
tQUIET
680
610
10
35
30
680
610
10
48
30
ns max
ns max
kHz min
MHz max
ns min
t1
t2
t3
10
40
0
10
40
0
ns min
ns min
ns min
t4
10
10
ns max
t5 2
t6
t7
t8
t9
tPOWER-UP
20
7
0.3 × tSCLK
0.3 × tSCLK
10
70
14
7
0.3 × tSCLK
0.3 × tSCLK
10
70
ns max
ns min
ns min
ns min
ns max
µs max
Parameter
tCONVERT
fSCLK
Test Conditions/Comments
Conversion time, internal clock; CNVST falling edge to
BUSY falling edge
AD7367
AD7366
Frequency of serial read clock
Minimum quiet time required between the end of serial
read and the start of the next conversion
Minimum CNVST low pulse
CNVST falling edge to BUSY rising edge
BUSY falling edge to MSB, valid when CS is low for t4 prior
to BUSY going low
Delay from CS falling edge until Pin 1 (DOUTA) and Pin 23
(DOUTB) are three-state disabled
Data access time after SCLK falling edge
SCLK to data valid hold time
SCLK low pulse width
SCLK high pulse width
CS rising edge to DOUTA, DOUTB, high impedance
Power-up time from shutdown mode; time required
between CNVST rising edge and CNVST falling edge
1
Sample tested during initial release to ensure compliance. All input signals are specified with tR = tF = 5 ns (10% to 90% of VDRIVE) and timed from a voltage level of 1.6 V.
All timing specifications are with a 25 pF load capacitance. With a load capacitance greater than 25 pF, a digital buffer or latch must be used. See the Terminology
section, Figure 25, and Figure 26.
2
The time required for the output to cross is 0.4 V or 2.4 V.
www.BDTIC.com/ADI/
ABSOLUTE MAXIMUM RATINGS
Table 5.
Parameter
VDD to AGND, DGND
VSS to AGND, DGND
VDRIVE to DGND
VDD to AVCC
AVCC to AGND, DGND
DVCC to AVCC
DVCC to DGND
VDRIVE to AGND
AGND to DGND
Analog Input Voltage to AGND
Digital Input Voltage to DGND
Digital Output Voltage to GND
DCAPA, DCAPB Input to AGND
Input Current to Any Pin Except
Supplies1
Operating Temperature Range
Storage Temperature Range
Junction Temperature
TSSOP Package
θJA Thermal Impedance
θJC Thermal Impedance
Pb-Free Temperature, Soldering Reflow
ESD
1
Rating
−0.3 V to +16.5 V
−16.5 V to +0.3 V
−0.3 V to DVCC
(VCC − 0.3 V) to +16.5 V
−0.3 V to +7 V
−0.3 V to +0.3 V
−0.3 V to +7 V
−0.3 V to DVCC
−0.3 V to +0.3 V
VSS − 0.3 V to VDD + 0.3 V
−0.3 V to VDRIVE + 0.3 V
−0.3 V to VDRIVE + 0.3 V
−0.3 V to AVCC + 0.3 V
±10 mA
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
ESD CAUTION
−40°C to +85°C
−65°C to +150°C
150°C
128°C/W
42°C/W
260°C
1.5 kV
Transient currents of up to 100 mA will not cause latch-up.
www.BDTIC.com/ADI/
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
DOUTA
1
24 DGND
VDRIVE
2
23 DOUTB
DVCC
3
RANGE1
RANGE0
ADDR
4
5
AGND
7
AVCC
8
17 AGND
DCAP A
9
16 DCAP B
VSS 10
VA1 11
VA2 12
21 CNVST
20 SCLK
TOP VIEW
(Not to Scale) 19 CS
18 REFSEL
15 VDD
14 VB1
13 VB2
06703-002
6
22 BUSY
AD7366/
AD7367
Figure 2. Pin Configuration
Table 6. Pin Function Descriptions
Pin No.
1, 23
Mnemonic
DOUTA, DOUTB
2
VDRIVE
3
DVCC
4, 5
6
RANGE1,
RANGE0
ADDR
7, 17
AGND
8
AVCC
9, 16
DCAPA, DCAPB
10
VSS
11, 12
VA1, VA2
13, 14
VB2, VB1
15
VDD
Description
Serial Data Outputs. The data output is supplied to each pin as a serial data stream. The bits are clocked out on
the falling edge of the SCLK input; 12 SCLK cycles are required to access a result from the AD7366, and 14 SCLK
cycles are required for the AD7367. The data simultaneously appears on both pins from the simultaneous conversions of both ADCs. The data stream consists of the 12 bits of conversion data for the AD7366 and 14 bits for
the AD7367 and is provided MSB first. If CS is held low for a further 14 SCLK cycles, on either DOUTA or DOUTB, the
data from the other ADC follows on that DOUT pin. Note, the second serial result from the AD7366 is preceeded
by two zeros. Therfore data from a simultaneous conversion on both ADCs can be gathered in serial format on
either DOUTA or DOUTB using only one serial port. See the Serial Interface section for more information.
Logic Power Supply Input. The voltage supplied at this pin determines at what voltage the interface operates.
This pin should be decoupled to DGND. The voltage range on this pin is 2.7 V to 5.25 V and may be different
from the voltage at AVCC and DVCC, but should never exceed either by more than 0.3 V. To achieve a throughput
rate of 1.12 MSPS for the AD7366 or 1 MSPS for the AD7367, VDRIVE must be ≥ 4.75 V.
Digital Supply Voltage, 4.75 V to 5.25 V. The DVCC and AVCC voltages should ideally be at the same potential.
For best performance, it is recommended that the DVCC and AVCC pins be shorted together, to ensure that the
voltage difference between them never exceeds 0.3 V even on a transient basis. This supply should be decoupled
to DGND. Place 10 µF and 100 nF decoupling capacitors on the DVCC pin.
Analog Input Range Selection, Logic Inputs. The polarity on these pins determines the input range of the analog
input channels. See the Analog Inputs section and Table 8 for details.
Multiplexer Select, Logic Input. This input is used to select the pair of channels to be simultaneously converted,
either Channel 1 of both ADC A and ADC B, or Channel 2 of both ADC A and ADC B. The logic state on this pin is
latched on the rising edge of BUSY to set up the multiplexer for the next conversion.
Analog Ground. Ground reference point for all analog circuitry on the AD7366/AD7367. All analog input signals
and any external reference signal should be referred to this AGND voltage. Both AGND pins should connect to
the AGND plane of a system. The AGND and DGND voltages should ideally be at the same potential and must
not be more than 0.3 V apart, even on a transient basis.
Analog Supply Voltage, 4.75 V to 5.25 V. This is the supply voltage for the ADC cores. The AVCC and DVCC voltages
should ideally be at the same potential. For best performance, it is recommended that the DVCC and AVCC pins be
shorted together, to ensure that the voltage difference between them never exceeds 0.3 V even on a transient
basis. This supply should be decoupled to AGND. Place 10 µF and 100 nF decoupling capacitors on the AVCC pin.
Decoupling Capacitor Pins. Decoupling capacitors are connected to these pins to decouple the reference buffer
for each respective ADC. For best performance, it is recommended that a 680 nF decoupling capacitor be used
on these pins. Provided the output is buffered, the on-chip reference can be taken from these pins and applied
externally to the rest of a system.
Negative Power Supply Voltage. This is the negative supply voltage for the high voltage analog input structure
of the AD7366/AD7367. The supply must be less than a maximum voltage of −11.5 V for all analog input ranges.
See Table 7 for more details. Place 10 µF and 100 nF decoupling capacitors on the VSS pin.
Analog Inputs of ADC A. Both analog inputs are single-ended. The analog input range on these channels is
determined by the RANGE0 and RANGE1 pins.
Analog Inputs of ADC B. Both analog inputs are single-ended. The analog input range on these channels is
determined by the RANGE0 and RANGE1 pins.
Positive Power Supply Voltage. This is the positive supply voltage for the high voltage analog input structure of
the AD7366/AD7367. The supply must be greater than a minimum voltage of 11.5 V for all analog input ranges.
See Table 7 for more details. Place 10 µF and 100 nF decoupling capacitors on the VDD pin.
www.BDTIC.com/ADI/
Pin No.
18
Mnemonic
REFSEL
19
CS
20
21
SCLK
CNVST
22
BUSY
24
DGND
Description
Internal/External Reference Selection, Logic Input. If this pin is tied to logic high, the on-chip 2.5 V reference is
used as the reference source for both ADC A and ADC B. In addition, Pin DCAPA and Pin DCAPB must be tied to
decoupling capacitors. If the REFSEL pin is tied to GND, an external reference can be supplied to the AD7366/
AD7367 through the DCAPA pin, the DCAPB pin, or both pins.
Chip Select, Active Low Logic Input. This input frames the serial data transfer. When CS is logic low, the output
bus is enabled and the conversion result is output on DOUTA and DOUTB.
Serial Clock, Logic Input. A serial clock input provides the SCLK for accessing the data from the AD7366/AD7367.
Conversion Start, Logic Input. This pin is edge triggered. On the falling edge of this input, the track/hold goes
into hold mode and the conversion is initiated. If CNVST is low at the end of a conversion, the part goes into
power-down mode. In this case, the rising edge of CNVST instructs the part to power up again.
Busy Output. BUSY transitions high when a conversion is started and remains high until the conversion
is complete.
Digital Ground. Ground reference point for all digital circuitry on the AD7366/AD7367. The DGND pin should
connect to the DGND plane of a system. The DGND and AGND voltages should ideally be at the same potential
and must not be more than 0.3 V apart, even on a transient basis.
www.BDTIC.com/ADI/
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 25°C, unless otherwise noted.
1.0
–76
0.8
0V TO 10V RANGE
0.6
0.2
THD (dB)
DNL ERROR (LSB)
–78
0.4
0
–0.2
±10V RANGE
–80
±5V RANGE
–82
–0.4
–1.0
0
2000
4000
6000
8000
10000 12000 14000 16000
CODE
–86
10
06703-003
–0.8
100
1000
ANALOG INPUT FREQUENCY (kHz)
Figure 6. THD vs. Analog Input Frequency
Figure 3. AD7367 Typical DNL
2.0
–66
1.5
1.0
–71
AVCC = 5V, DVCC = 5V
VDD = 15V, VSS = –15V
VDRIVE = 3V
fS = 1MSPS
INTERNAL REFERENCE
±5V RANGE
RIN = 2000Ω
THD (dB)
0.5
0
RIN = 1300Ω
RIN = 3000Ω
–76
RIN = 470Ω
RIN = 5100Ω
–0.5
AVCC = 5V, DVCC = 5V
VDD = 15V, VSS = –15V
VDRIVE = 3V
fS = 1MSPS
TA = 25°C
INTERNAL REFERENCE
–1.5
–2.0
0
2000
4000
6000
8000
–81
RIN = 56Ω
10000 12000 14000 16000
CODE
–86
10
RIN = 240Ω
RIN = 3900Ω
100
1000
ANALOG INPUT FREQUENCY (kHz)
06703-007
–1.0
06703-004
INL ERROR (LSB)
AVCC = 5V, DVCC = 5V
VDD = 15V, VSS = –15V
VDRIVE = 3V
fS = 1MSPS
INTERNAL REFERENCE
–84
06703-006
AVCC = 5V, DVCC = 5V
VDD = 15V, VSS = –15V
VDRIVE = 3V
fS = 1MSPS
TA = 25°C
INTERNAL REFERENCE
–0.6
Figure 7. THD vs. Analog Input Frequency for Various Source Impedances
Figure 4. AD7367 Typical INL
0
AVCC = 5V, DVCC = 5V
VDD = 15V, VSS = –15V
VDRIVE = 3V
fS = 1MSPS, fIN = 50kHz
INTERNAL REFERENCE
SNR = 76dB, SINAD = 75dB
–40
77
SINAD (dB)
–80
–100
73
69
–140
–160
50
100
150
200
250
300
FREQUENCY (kHz)
Figure 5. AD7367 FFT
350
400
450
500
0V TO 10V RANGE
71
–120
06703-005
(dB)
–60
0
±10V RANGE
75
67
10
AVCC = 5V, DVCC = 5V
VDD = 15V, VSS = –15V
VDRIVE = 3V
fS = 1MSPS
INTERNAL REFERENCE
±5V RANGE
100
ANALOG INPUT FREQUENCY (kHz)
Figure 8. SINAD vs. Analog Input Frequency
www.BDTIC.com/ADI/
1000
06703-008
–20
80
AVCC = 5V, DVCC = 5V
VDD = 15V, VSS = –15V
VDRIVE = 3V
fS = 1MSPS
INTERNAL REFERENCE
–75
–80
±5V RANGE
–85
0V TO 10V RANGE
–90
–95
±10V RANGE
–100
AVCC = 5V, DVCC = 5V
VDD = 15V, VSS = –15V
VDRIVE = 3V
fS = 1MSPS
INTERNAL REFERENCE
–105
–110
0
100
200
300
400
500
600
FREQUENCY OF INPUT NOISE (kHz)
40
VIN = +5V
20
VIN = +10V
0
–40
100
VIN = –5V
200
300
400
500
600
700
800
900
1000
THROUGHPUT RATE (kSPS)
Figure 12. Analog Input Current vs. Throughput Rate
2.5050
106091 CODES
31 CODES
100000
VIN = –10V
–20
Figure 9. Channel-to-Channel Isolation
110000
VIN = 0V TO 10V
06703-012
ANALOG INPUT CURRENT (µA)
60
06703-009
CHANNEL-TO-CHANNEL ISOLATION (dB)
–70
344 CODES
2.5045
90000
2.5040
80000
2.5035
70000
VREF (V)
2.5030
60000
50000
40000
2.5025
2.5020
2.5015
20000
2.5010
10000
2.5005
8191
8192
8193
8194
8195
06703-010
0
8196
CODE
AVCC = 5V, DVCC = 5V
VDD = 15V, VSS = –15V
VDRIVE = 3V
2.5000
0
10
20
30
40
50
60
70
80
CURRENT LOAD (µA)
Figure 10. Histogram of Codes for 200k Samples
06703-013
30000
Figure 13. VREF vs. Reference Output Current Drive
0.300
–70
VCC, ADC A
SOURCE CURRENT
–90
VDD, ADC B
–100
VSS, ADC B
VDD, ADC A
–110
400
600
800
SUPPLY RIPPLE FREQUENCY (kHz)
1000
1200
06703-011
–120
200
SINK CURRENT
0.150
0.100
AVCC = 5V, DVCC = 5V
VDD = 15V, VSS = –15V
VDRIVE = 3V, fS = 1MSPS
INTERNAL REFERENCE
0.50
VSS, ADC A
0
0.200
Figure 11. PSRR vs. Supply Ripple Frequency Without Supply Decoupling
0
0
500
1000
1500
CURRENT (µA)
2000
2500
06703-014
VOUT OR VCC – VOUT (V)
PSRR (dB)
0.250
100mV p-p SINE WAVE ON AVCC
NO DECOUPLING CAPACITOR
VDD = 15V, VSS = –15V
VCC, ADC B
VDRIVE = 3V
fS = 1MSPS
–80
Figure 14. DOUT Source Current vs. (VCC − VOUT ) and DOUT Sink Current vs. VOUT
www.BDTIC.com/ADI/
65
AVCC = 5V, DVCC = 5V
VDD = 15V, VSS = –15V
VDRIVE = 3V
fS = 1MSPS
INTERNAL REFERENCE
0V TO 10V RANGE
±5V RANGE
45
35
±10V RANGE
25
15
100
200
300
400
500
600
700
800
900
1000
SAMPLING FREQUENCY (kSPS)
06703-017
POWER (mV)
55
Figure 15. Power vs. Sampling Frequency in Normal Mode
www.BDTIC.com/ADI/
TERMINOLOGY
Differential Nonlinearity (DNL)
DNL is the difference between the measured and the ideal
1 LSB change between any two adjacent codes in the ADC.
Integral Nonlinearity (INL)
INL is the maximum deviation from a straight line passing
through the endpoints of the ADC transfer function. The
endpoints of the transfer function are zero scale, a point 1 LSB
below the first code transition, and full scale, a point 1 LSB above
the last code transition.
Zero Code Error
The deviation of the midscale transition (all 1s to all 0s) from
the ideal VIN voltage, that is, AGND − ½ LSB for bipolar ranges
and 2 × VREF − 1 LSB for the unipolar range.
Positive Full-Scale Error
The deviation of the last code transition (011…110) to (011…111)
from the ideal (that is, +4 × VREF − 1 LSB or +2 × VREF – 1 LSB)
after the zero code error has been factored out.
Negative Full-Scale Error
The deviation of the first code transition (10…000) to (10…001)
from the ideal (that is, −4 × VREF + 1 LSB, −2 × VREF + 1 LSB, or
AGND + 1 LSB) after the zero code error has been factored out.
Zero Code Error Match
The difference in zero code error across all channels.
Positive Full-Scale Error Match
The difference in positive full-scale error across all channels.
Negative Full-Scale Error Match
The difference in negative full-scale error across all channels.
Track-and-Hold Acquisition Time
The track-and-hold amplifier returns to track mode at the end
of a conversion. Track-and-hold acquisition time is the time
required for the output of the track-and-hold amplifier to reach
its final value, within ±½ LSB, after the end of a conversion.
Signal-to-Noise (+ Distortion) Ratio (SINAD)
This ratio is the measured ratio of signal-to-noise (+ distortion)
at the output of the ADC. The signal is the rms amplitude of the
fundamental. Noise is the sum of all nonfundamental signals up
to half the sampling frequency (fS/2), excluding dc. The ratio is
dependent on the number of quantization levels in the digitization process: the more levels, the smaller the quantization noise.
The theoretical signal-to-noise (+ distortion) ratio for an ideal
N-bit converter with a sine wave input is as follows:
Signal-to-Noise (+ Distortion) = (6.02N + 1.76) dB
Thus, for a 12-bit converter, the SINAD is 74 dB.
Total Harmonic Distortion (THD)
THD is the ratio of the rms sum of harmonics to the fundamental.
For the AD7366/AD7367, THD is defined as follows:
THD(dB) = 20 log
V 2 2 + V 3 2 + V 4 2 + V 5 2 + V6 2
V1
where:
V1 is the rms amplitude of the fundamental.
V2, V3, V4, V5, and V6 are the rms amplitudes of the second
through the sixth harmonics.
Peak Harmonic or Spurious Noise
Peak harmonic, or spurious noise, is the ratio of the rms value
of the next largest component in the ADC output spectrum
(up to fS/2, excluding dc) to the rms value of the fundamental.
Normally, the value of this specification is determined by the
largest harmonic in the spectrum. However, for ADCs where
the harmonics are buried in the noise floor, it is a noise peak.
Channel-to-Channel Isolation
Channel-to-channel isolation is a measure of the level of crosstalk between any two channels when operating in any of the
input ranges. It is measured by applying a full-scale, 150 kHz
sine wave signal to all unselected input channels and determining
how much that signal is attenuated in the selected channel with
a 50 kHz signal. The figure given is the typical value across all
four channels for the AD7366/AD7367 (see Figure 9 for more
information).
Intermodulation Distortion (IMD)
With inputs consisting of sine waves at two frequencies, fa and
fb, any active device with nonlinearities creates distortion products at the sum, and different frequencies of mfa ± nfb, where
m, n = 0, 1, 2, 3, and so on. Intermodulation distortion terms
are those for which neither m nor n is equal to zero. For example,
the second-order terms include (fa + fb) and (fa − fb), and the
third-order terms include (2fa + fb), (2fa − fb), (fa + 2fb), and
(fa − 2fb).
The AD7366/AD7367 are tested using the CCIF standard where
two input frequencies near the top end of the input bandwidth
are used. In this case, the second-order terms are usually distanced
in frequency from the original sine waves, and the third-order
terms are usually at a frequency close to the input frequencies.
As a result, the second- and third-order terms are specified
separately. The calculation of the intermodulation distortion is
as per the THD specification, where it is the ratio of the rms
sum of the individual distortion products to the rms amplitude
of the sum of the fundamentals expressed in decibels.
www.BDTIC.com/ADI/
Power Supply Rejection Ratio (PSRR)
Variations in power supply affect the full-scale transition but
not the converter’s linearity. PSRR is the maximum change in
the full-scale transition point due to a change in power supply
voltage from the nominal value (see Figure 11).
Thermal (or Output Voltage) Hysteresis
Thermal (or output voltage) hysteresis is defined as the absolute
maximum change of reference output voltage after the device is
cycled through temperature from either
It is expressed in ppm using the following equation:
VHYS (ppm) =
VREF (25°C) − VREF (T _ HYS)
VREF (25°C)
× 10 6
where:
VREF(25°C) is VREF at 25°C.
VREF(T_HYS) is the maximum change of VREF at T_HYS+
or T_HYS−.
T_HYS+ = +25°C to TMAX to +25°C
or
T_HYS− = +25°C to TMIN to +25°C
www.BDTIC.com/ADI/
THEORY OF OPERATION
CIRCUIT INFORMATION
CONVERTER OPERATION
The AD7366/AD7367 are fast, dual, 2-channel, 12-/14-bit,
bipolar input, simultaneous sampling, serial ADCs. The
AD7366/AD7367 can accept bipolar input ranges of ±10 V
and ±5 V. They can also accept a unipolar input range of 0 V to
10 V. The AD7366/AD7367 require VDD and VSS dual supplies
for the high voltage analog input structures. These supplies must
be equal to or greater than ±11.5 V. See Table 7 for the minimum
requirements on these supplies for each analog input range. The
AD7366/AD7367 require a low voltage 4.75 V to 5.25 V AVCC
supply to power the ADC core.
The AD7366/AD7367 have two successive approximation
ADCs, each based around two capacitive DACs. Figure 16 and
Figure 17 show simplified schematics of an ADC in acquisition
and conversion phases. The ADC comprises control logic, a
SAR, and a capacitive DAC. In Figure 16 (the acquisition phase),
SW2 is closed and SW1 is in Position A, the comparator is held
in a balanced condition, and the sampling capacitor arrays
acquire the signal on the input.
Table 7. Reference and Supply Requirements for Each
Analog Input Range
±10
±5
0 to 10
VIN
A
SW1
CONTROL
LOGIC
B
SW2
Full-Scale
Input
Range (V)
AVCC (V)
Minimum
VDD/VSS (V)
2.5
3.0
2.5
3.0
2.5
3.0
±10
±12
±5
±6
0 to 10
0 to 12
5
5
5
5
5
5
±11.5
±12
±11.5
±11.5
±11.5
±12
The AD7366/AD7367 contain two on-chip, track-and-hold
amplifiers, two successive approximation ADCs, and a serial
interface with two separate data output pins. The AD7366/AD7367
are available in a 24-lead TSSOP, offering the user considerable
space-saving advantages over alternative solutions. The AD7366/
AD7367 require a CNVST signal to start conversion. On the
falling edge of CNVST, both track-and-holds are placed into
hold mode and the conversions are initiated. The BUSY signal
goes high to indicate that the conversions are taking place. The
clock source for each successive approximation ADC is provided
by an internal oscillator. The BUSY signal goes low to indicate
the end of conversion. On the falling edge of BUSY, the trackand-hold returns to track mode. When the conversion is
finished, the serial clock input accesses data from the part.
The AD7366/AD7367 have an on-chip 2.5 V reference that can
be disabled if an external reference is preferred. If the internal
reference is to be used elsewhere in a system, the output from
DCAPA and DCAPB must first be buffered. On power-up, the
REFSEL pin must be tied to either a high or low logic state to
select either the internal or external reference option. If the
internal reference is the preferred option, the user must tie the
REFSEL pin logic high. Alternatively, if REFSEL is tied to GND
then an external reference can be supplied to both ADCs
through the DCAPA and DCAPB pins.
The analog inputs are configured as two single-ended inputs
for each ADC. The input voltage range can be selected by
programming the RANGE bits as shown in Table 8.
COMPARATOR
06703-018
Reference
Voltage (V)
AGND
Figure 16. ADC Acquisition Phase
When the ADC starts a conversion (see Figure 17), SW2 opens
and SW1 moves to Position B, causing the comparator to
become unbalanced. The control logic and the charge redistribution DAC are used to add and subtract fixed amounts of
charge from the sampling capacitor to bring the comparator
back into a balanced condition. When the comparator is
balanced again, the conversion is complete. The control logic
generates the ADC output code.
CAPACITIVE
DAC
VIN
A
SW1
CONTROL
LOGIC
B
SW2
COMPARATOR
AGND
06703-019
Selected
Analog Input
Range (V)
CAPACITIVE
DAC
Figure 17. ADC Conversion Phase
ANALOG INPUTS
Each ADC in the AD7366/AD7367 has two single-ended
analog inputs. Figure 18 shows the equivalent circuit of the
analog input structure of the AD7366/AD7367. The two diodes
provide ESD protection. Care must be taken to ensure that the
analog input signals never exceed the supply rails by more than
300 mV. This causes these diodes to become forward-biased
and to start conducting current into the substrate. These diodes
can conduct up to 10 mA without causing irreversible damage
to the part. The resistors are lumped components made up of
the on resistance of the switches. The value of these resistors is
typically about 170 Ω. Capacitor C1 can primarily be attributed
to pin capacitance, while Capacitor C2 is the sampling capacitor
of the ADC. The total lumped capacitance of C1 and C2 is
approximately 9 pF for the ±10 V input range and approximately 13 pF for all other input ranges.
www.BDTIC.com/ADI/
Table 10. LSB Sizes for Each Analog Input Range
R1
C1
C2
06703-020
D
VSS
Figure 18. Equivalent Analog Input Structure
The AD7366/AD7367 can handle true bipolar input voltages.
The analog input can be set to one of three ranges: ±10 V, ±5 V,
or 0 V to 10 V. The logic levels on Pin RANGE0 and Pin RANGE1
determine which input range is selected as outlined in Table 8.
These range bits should not be changed during the acquisition
time prior to a conversion, but can be changed at any other time.
Table 8. Analog Input Range Selection
RANGE1
0
0
1
1
RANGE0
0
1
0
1
Range Selected
±10 V
±5 V
0 V to 10 V
Do not program
The AD7366/AD7367 require VDD and VSS dual supplies for the
high voltage analog input structures. These supplies must be
equal to or greater than ±11.5 V. See Table 7 for the requirements on these supplies. The AD7366/AD7367 require a low
voltage 4.75 V to 5.25 V AVCC supply to power the ADC core,
a 4.75 V to 5.25 V DVCC supply for digital power, and a 2.7 V
to 5.25 V VDRIVE supply for interface power.
Channel selection is made via the ADDR pin, as shown in
Table 9. The logic level on the ADDR pin is latched on the
rising edge of the BUSY signal for the next conversion, not
the one in progress. When power is first supplied to the
AD7366/AD7367, the default channel selection is VA1 and VB1.
Table 9. Channel Selection
ADDR
0
1
Channels Selected
VA1, VB1
VA2, VB2
TRANSFER FUNCTION
The output coding of the AD7366/AD7367 is twos complement.
The designed code transitions occur at successive integer LSB
values (that is, 1 LSB, 2 LSB, and so on). The LSB size is dependent
on the analog input range selected (see Table 10). The ideal
transfer characteristic is shown in Figure 19.
Input
Range
±10 V
±5 V
0 V to 10 V
AD7366
Full-Scale LSB Size
Range
(mV)
20 V/4096
4.88
10 V/4096
2.44
10 V/4096
2.44
AD7367
Full-Scale
LSB Size
Range
(mV)
20 V/16,384 1.22
10 V/16,384 0.61
10 V/16,384 0.61
011...111
011...110
000...001
000...000
111...111
100...010
100...001
100...000
+FSR/2 – 1LSB
0V
ANALOG INPUT
–FSR/2 + 1LSB
06703-021
D
VIN
ADC CODE
VDD
Figure 19. Transfer Characteristic
Track-and-Hold
The track-and-hold on the analog input of the AD7366/AD7367
allows the ADC to accurately convert an input sine wave of fullscale amplitude to 12-/14-bit accuracy. The input bandwidth of
the track-and-hold is greater than the Nyquist rate of the ADC.
The AD7366/AD7367 can handle frequencies up to 35 MHz.
The track-and-hold enters its tracking mode when the BUSY
signal goes low after the CS falling edge. The time required to
acquire an input signal depends on how quickly the sampling
capacitor is charged. With zero source impedance, 140 ns is sufficient to acquire the signal to the 12-bit level for the AD7366 and
the 14-bit level for the AD7367. The acquisition time for the
±10 V, ±5 V, and 0 V to 10 V ranges to settle to within ±½ LSB
is typically 140 ns. The ADC returns to hold mode on the
falling edge of CNVST.
The acquisition time required is calculated using the following
formula:
tACQ = 10 × ((RSOURCE + R) C)
where:
C is the sampling capacitance.
R is the resistance seen by the track-and-hold amplifier looking
at the input.
RSOURCE should include any extra source impedance on the
analog input.
www.BDTIC.com/ADI/
TYPICAL CONNECTION DIAGRAM
Unlike other bipolar ADCs, the AD7366/AD7367 do not have a
resistive analog input structure. On the AD7366/AD7367, the
bipolar analog signal is sampled directly onto the sampling
capacitor. This gives the AD7366/AD7367 high analog input
impedance. The analog input impedance can be calculated from
the following formula:
Figure 20 shows a typical connection diagram for the AD7366/
AD7367. In this configuration, the AGND pin is connected
to the analog ground plane of the system, and the DGND pin
is connected to the digital ground plane of the system. The
analog inputs on the AD7366/AD7367 accept bipolar singleended signals. The AD7366/AD7367 can operate with either
an internal or an external reference. In Figure 20, the AD7366/
AD7367 are configured to operate with the internal 2.5 V reference.
A 680 nF decoupling capacitor is required when operating with
the internal reference.
Z = 1/(fS × CS)
where:
fS is the sampling frequency.
CS is the sampling capacitor value.
CS depends on the analog input range chosen (see the Analog
Inputs section). When operating at 1 MSPS, the analog input
impedance is typically 260 kΩ for the ±10 V range. As the
sampling frequency is reduced, the analog input impedance
further increases. As the analog input impedance increases, the
current required to drive the analog input therefore decreases
(see Figure 7 for more information).
The AVCC and DVCC pins are connected to a 5 V supply voltage.
The VDD and VSS are the dual supplies for the high voltage analog
input structures. The voltage on these pins must be equal to or
greater than ±11.5 V (see Table 7 for more information). The
VDRIVE pin is connected to the supply voltage of the microprocessor.
The voltage applied to the VDRIVE input controls the voltage of
the serial interface. VDRIVE can be set to 3 V or 5 V.
+
0.1µF
+5V SUPPLY
+
10µF
+
0.1µF
0.1µF
VDD
+
10µF
DVCC AVCC
+3V OR +5V SUPPLY
VDRIVE
VA1
AD7366/
AD7367
VA2
0.1µF
+
10µF
+
CS
ANALOG INPUTS ±10V,
±5V, AND 0V TO +10V
SCLK
CNVST
DOUTA
VB1
DOUTB
BUSY
VB2
ADDR
DCAP A
680nF
+
680nF
+
DCAP B
VSS
REFSEL
VDRIVE
RANGE0
RANGE1
DGND
AGND
–16.5V TO –11.5V
SUPPLY
10µF
+
0.1µF
+
SERIAL
INTERFACE
06703-022
+
MICROCONTROLLER/
MICROPROCESSOR
+11.5V TO +16.5V
SUPPLY
Figure 20. Typical Connection Diagram Using Internal Reference
www.BDTIC.com/ADI/
DRIVER AMPLIFIER CHOICE
VDRIVE
The AD7366/AD7367 have a total of four analog inputs, which
operate in single-ended mode. The analog inputs for both ADCs
can be programmed to one of the three analog input ranges. In
applications where the signal source is high impedance, it is
recommended that the signal be buffered before applying it to
the ADC analog inputs. Figure 21 shows the configuration of
the AD7366/AD7367 in single-ended mode.
The AD7366/AD7367 also have a VDRIVE feature to control the
voltage at which the serial interface operates. VDRIVE allows the
ADC to easily interface to both 3 V and 5 V processors. For
example, if the AD7366/AD7367 were operated with a VCC of
5 V, the VDRIVE pin could be powered from a 3 V supply, allowing
a large dynamic range with low voltage digital processors. Thus,
the AD7366/AD7367 can be used with the ±10 V input range
while still being able to interface to 3 V digital parts.
In applications where the THD and SNR are critical specifications, the analog input of the AD7366/AD7367 should be
driven from a low impedance source. Large source impedances
significantly affect the ac performance of the ADC and can
necessitate the use of an input buffer amplifier.
When no amplifier is used to drive the analog input, the source
impedance should be limited to low values. The maximum source
impedance depends on the amount of THD that can be tolerated
in the application. The THD increases as the source impedance
increases and performance degrades. Figure 7 shows THD vs.
the analog input frequency for various source impedances.
Depending on the input range and analog input configuration
selected, the AD7366/AD7367 can handle source impedances as
illustrated in Figure 7.
To achieve the maximum throughput rate of 1.12 MSPS for the
AD7366 or 1 MSPS for the AD7367, VDRIVE must be greater than
or equal to 4.75 V (see Table 2 and Table 3). The maximum
throughput rate with the VDRIVE voltage set to less than 4.75 V
and greater than 2.7 V is 1 MSPS for the AD7366 and 900 kSPS
for the AD7367.
REFERENCE
Due to the programmable nature of the analog inputs on the
AD7366/AD7367, the choice of op amp used to drive the
inputs is a function of the particular application and depends
on the analog input voltage range selected.
The AD7366/AD7367 can operate with either the internal 2.5 V
on-chip reference or an externally applied reference. The logic
state of the REFSEL pin determines whether the internal reference is used. The internal reference is selected for both ADCs
when the REFSEL pin is tied to logic high. If the REFSEL pin is
tied to GND, an external reference can be supplied through the
DCAPA and DCAPB pins. On power-up, the REFSEL pin must be
tied to either a low or high logic state for the part to operate.
Suitable reference sources for the AD7366/AD7367 include the
AD780, AD1582, ADR431, REF193, and ADR391.
The driver amplifier must be able to settle for a full-scale step
to a 14-bit level, 0.0061%, in less than the specified acquisition
time of the AD7366/AD7367. An op amp such as the AD8021
meets this requirement when operating in single-ended mode.
The AD8021 needs an external compensating NPO type of
capacitor. The AD8022 can also be used in high frequency
applications where a dual version is required. For lower frequency applications, recommended op amps are the AD797,
AD845, and AD8610.
The internal reference circuitry consists of a 2.5 V band gap
reference and a reference buffer. When operating the AD7366/
AD7367 in internal reference mode, the 2.5 V internal reference
is available at the DCAPA and DCAPB pins, which should be
decoupled to AGND using a 680 nF capacitor. It is recommended that the internal reference be buffered before applying
it elsewhere in the system. The internal reference is capable of
sourcing up to 150 μA with an analog input range of ±10 V
and 70 μA for both the ±5 V and 0 V to 10 V ranges.
If the internal reference operation is required for the ADC conversion, the REFSEL pin must be tied to logic high on power-up.
The reference buffer requires 70 µs to power up and charge the
680 nF decoupling capacitor during the power-up time.
+
V+
10µF
+5V
+
+10V/+5V
0.1µF
+
AGND
AD8021
VA1
–10V/–5V
+
1kΩ
VDD
The AD7366/AD7367 are specified for a 2.5 V to 3 V reference.
When a 3 V reference is selected, the analog input ranges are
±12 V, ±6 V, and 0 V to 12 V. For these ranges, the VDD supply
must be greater than or equal to +12 V and the VSS supply must
be less than or equal to −12 V.
VCC
AD7366/
AD7367*
1kΩ
15pF
VSS
+
0.1µF
CCOMP = 10pF
V–
*ADDITIONAL PINS OMITTED FOR CLARITY.
06703-023
10µF
Figure 21. Typical Connection Diagram with the AD8021 for Driving the
Analog Input
www.BDTIC.com/ADI/
MODES OF OPERATION
The mode of operation of the AD7366/AD7367 is selected by
the logic state of the CNVST signal at the end of a conversion.
There are two possible modes of operation: normal mode and
shutdown mode. These modes of operation are designed to
provide flexible power management options, which can be
chosen to optimize the power dissipation/throughput rate
ratio for differing application requirements.
The CS pin must be brought low to bring the data bus out of
three-state. Therefore, 12 SCLK cycles are required to read the
conversion result from the AD7366 and 14 SCLK cycles are
required to read the conversion result from the AD7367. The
DOUT lines return to three-state only when CS is brought high. If
CS is left low for an additional 12 SCLK cycles for the AD7366 or
14 SCLK cycles for the AD7367, the result from the other on-chip
ADC is also accessed on the same DOUT line, as shown in Figure 27
and Figure 28 (see the Serial Interface section).
NORMAL MODE
Normal mode is intended for applications that require fast
throughput rates. In normal mode, the AD7366/AD7367
remain fully powered at all times, so the user does not need to
worry about power-up times. Figure 22 shows the general mode
of operation of the AD7366 in normal mode; Figure 23 shows
normal mode for the AD7367.
When 24 SCLK cycles have elapsed for the AD7366 or 28 SCLK
cycles for the AD7367, the DOUT line returns to three-state only
when CS is brought high, not on the 24th or 28th SCLK falling
edge. If CS is brought high prior to this, the DOUT line returns to
three-state at that point. Thus, CS must be brought high when
the read is completed, because the bus does not automatically
return to three-state upon completion of the dual result read.
The conversion is initiated on the falling edge of CNVST as
described in the Circuit Information section. To ensure that
the part remains fully powered up at all times, CNVST must be
at logic state high before the BUSY signal goes low. If CNVST is
at logic state low when the BUSY signal goes low, the analog
circuitry powers down and the part ceases converting. The
BUSY signal remains high for the duration of the conversion.
When a data transfer is complete and DOUTA and DOUTB have
returned to three-state, another conversion can be initiated after
the quiet time, tQUIET, has elapsed by bringing CNVST low again.
t1
CNVST
tQUIET
t2
BUSY
tCONVERT
t3
12
06703-024
SCLK
14
06703-025
CS
SERIAL READ OPERATION
1
Figure 22. Normal Mode Operation for the AD7366
t1
CNVST
tQUIET
t2
BUSY
tCONVERT
t3
CS
SCLK
SERIAL READ OPERATION
1
Figure 23. Normal Mode Operation for the AD7367
www.BDTIC.com/ADI/
SHUTDOWN MODE
POWER-UP TIMES
Shutdown mode is intended for use in applications where slow
throughput rates are required. Shutdown mode is suited to
applications where a series of conversions performed at a
relatively high throughput rate are followed by a long period
of inactivity and thus, shutdown. When the AD7366/AD7367
are in full power-down, all analog circuitry is powered down.
The falling edge of CNVST initiates the conversion. The BUSY
output subsequently goes high to indicate that the conversion is
in progress. After the conversion is completed, the BUSY output
returns low. If the CNVST signal is at logic low when BUSY
goes low, the part enters shutdown at the end of the conversion
phase. While the part is in shutdown mode, the digital output
code from the last conversion on each ADC can still be read
from the DOUT pins. To read the DOUT data, CS must be brought
low as described in the Serial Interface section. The DOUT pins
return to three-state when CS is brought back to logic high.
The AD7366/AD7367 have one power-down mode, which is
described in detail in the Shutdown Mode section. This section
deals with the power-up time required when coming out of
shutdown mode. It should be noted that the power-up times (as
explained in this section) apply with the recommended capacitors in place on the DCAPA and DCAPB pins. To power up from
shutdown, CNVST must be brought high and remain high for a
minimum of 70 μs, as shown in Figure 24.
When power supplies are first applied to the AD7366/AD7367,
the ADC can power up with CNVST in either the low or high
logic state. Before attempting a valid conversion, CNVST must
be brought high and remain high for the recommended powerup time of 70 μs. Then CNVST can be brought low to initiate a
conversion. With the AD7366/AD7367, no dummy conversion
is required before valid data can be read from the DOUT pins.
To place the part in shutdown mode when the supplies are first
applied, the AD7366/AD7367 must be powered up and a
conversion initiated. However, CNVST should remain in the
logic low state so that when the BUSY signal goes low, the part
enters shutdown.
To exit full power-down and to power up the AD7366/AD7367,
a rising edge of CNVST is required. After the required power-up
time has elapsed, CNVST can be brought low again to initiate
another conversion, as shown in Figure 24 (see the Power-Up
Times section for power-up times associated with the AD7366/
AD7367).
When supplies are applied to the AD7366/AD7367, sufficient
time must be allowed for any external reference to power up and
to charge the various reference buffer decoupling capacitors to
their final values.
tPOWER-UP
ENTERS SHUTDOWN
CNVST
BUSY
t2
tCONVERT
SCLK
SERIAL READ OPERATION
1
12
Figure 24. Autoshutdown Mode for the AD7366
www.BDTIC.com/ADI/
06703-026
t3
CS
SERIAL INTERFACE
Figure 25 and Figure 26 show the detailed timing diagram for
serial interfacing to the AD7366 and the AD7367. On the
falling edge of CNVST, the AD7366/AD7367 simultaneously
convert the selected channels. These conversions are performed
using the on-chip oscillator. After the falling edge of CNVST,
the BUSY signal goes high, indicating that the conversion has
started. The BUSY signal returns low when the conversion has
been completed. The data can now be read from the DOUT pins.
The CS and SCLK signals are required to transfer data from the
AD7366/AD7367. The AD7366/AD7367 have two output pins
corresponding to each ADC. Data can be read from the AD7366/
AD7367 using both DOUTA and DOUTB. Alternatively, a single
output pin of the user’s choice can be used. The SCLK input
signal provides the clock source for the serial interface. The CS
goes low to access data from the AD7366/AD7367. The falling
edge of CS takes the bus out of three-state and clocks out the
MSB of the conversion result. The data stream consists of
12 bits of data for the AD7366 and 14 bits of data for the
AD7367, MSB first. The first bit of the conversion result is
valid on the first SCLK falling edge after the CS falling edge.
The subsequent 11/13 bits of data for the AD7366/AD7367,
respectively, are clocked out on the falling edge of the SCLK
signal. A minimum of 12 clock pulses must be provided to the
AD7366 to access each conversion result, and a minimum of
14 clock pulses must be provided to the AD7367 to access the
conversion result. Figure 25 shows how a 12 SCLK read is used
to access the conversion results for the AD7366, and Figure 26
illustrates the case for the AD7367 with a 14 SCLK read.
On the rising edge of CS the conversion is terminated and
DOUTA and DOUTB return to three-state. If CS is not brought
high, but is instead held low for an additional 14 SCLK cycles
the data from the other DOUT pin follows on the selected
DOUT pin. Note, the second serial result from the AD7366 is
preceeded by two zeros. See Figure 27 and Figure 28, where
DOUTA is shown. In this case, the DOUT line in use returns to
three-state on the rising edge of CS.
If the falling edge of SCLK coincides with the falling edge of CS,
the falling edge of SCLK is not acknowledged by the AD7366/
AD7367, and the next falling edge of SCLK is the first one
registered after the falling edge of CS.
The CS pin can be brought low before the BUSY signal goes
low, indicating the end of a conversion. When CS is at a logic
low state, the data bus is brought out of three-state. This feature
can be used to ensure that the MSB is valid on the falling edge
of BUSY by bringing CS low a minimum of t4 before the BUSY
signal goes low. The dotted CS line in Figure 22 and Figure 23
illustrates this feature.
Alternatively, the CS pin can be tied to a low logic state continuously. In this case, the DOUT pins never enter three-state and the
data bus is continuously active. Under these conditions, the MSB
of the conversion result for the AD7366/AD7367 is available on
the falling edge of the BUSY signal. The next most significant
bit is available on the first SCLK falling edge after the BUSY
signal has gone low. This mode of operation enables the user to
read the MSB as soon as it is made available by the converter.
CS
t8
DOUTA
DOUTB
3
2
1
4
DB10
12
t6
t5
t4
THREESTATE
5
DB2
DB8
DB9
t9
t7
DB1
DB0
THREE-STATE
DB11
06703-027
SCLK
Figure 25. Serial Interface Timing Diagram for the AD7366
CS
t8
DOUTA
DOUTB THREESTATE
1
3
2
4
5
t5
t4
DB12
DB11
DB10
14
t6
t9
t7
DB2
DB1
DB13
DB0
THREE-STATE
Figure 26. Serial Interface Timing Diagram for the AD7367
www.BDTIC.com/ADI/
06703-028
SCLK
CS
t8
SCLK
3
2
1
4
5
10
12
11
13
14
26
t7
t5
t6
DB1 A
DB9 A
DB0 A
0
0
DB11B
DB1 B
DB0 B
THREESTATE
06703-030
THREESTATE DB11 A
DB10 A
THREESTATE
06703-029
t4
DOUTA
Figure 27. Reading Data from Both ADCs on One DOUT Line with 26 SCLKs for the AD7366
CS
t8
SCLK
3
2
1
4
5
12
14
13
15
28
t7
t4
DOUTA
THREE- DB13
A
STATE
DB12 A
t5
DB11A
t6
DB1 A
DB0 A
DB13 B
DB12 B
DB1 B
DB0 B
Figure 28. Reading Data from Both ADCs on One DOUT Line with 28 SCLKs for the AD7367
www.BDTIC.com/ADI/
MICROPROCESSOR INTERFACING
ADSP-218x*
AD7366/
AD7367*
SCLK0
SCLK
SCLK1
TFS0
CS
RFS0
AD7366/AD7367 TO ADSP-218x
Table 11. SPORT0 Control Register Setup
Setting
TFSW = RFSW = 1
INVRFS = INVTFS = 1
DTYPE = 00
SLEN = 1111
ISCLK = 1
TFSR = RFSR = 1
IRFS = 0
ITFS = 1
Description
Alternate framing
Active low frame signal
Right-justify data
16-bit data-word (or can be set to 1101
for 14-bit data-word)
Internal serial clock
Frame every word
Table 12. SPORT1 Control Register Setup
Setting
TFSW = RFSW = 1
INVRFS = INVTFS = 1
DTYPE = 00
SLEN = 1111
ISCLK = 0
TFSR = RFSR = 1
IRFS = 0
ITFS = 1
Description
Alternate framing
Active low frame signal
Right-justify data
16-bit data-word (or can be set to 1101
for 14-bit data-word)
External serial clock
Frame every word
DR0
DOUTB
DR1
BUSY
IRQ
CNVST
FLO
VDRIVE
VDD
*ADDITIONAL PINS OMITTED FOR CLARITY.
Figure 29. Interfacing the AD7366/AD7367 to the ADSP-218x
The AD7366/AD7367 BUSY line provides an interrupt to
the ADSP-218x when the conversion is complete. The conversion results can then be read from the AD7366/AD7367 using
a read operation. When an interrupt is received on IRQ from
the BUSY signal, a value is transmitted with TFS/DT (ADC
control word). The TFS is used to control the RFS and, therefore,
the reading of data.
AD7366/AD7367 TO ADSP-BF53x
The ADSP-BF53x family of DSPs interfaces directly to the
AD7366/AD7367 without any glue logic required. The availability of secondary receive registers on the serial ports of the
Blackfin® DSPs means that only one serial port is necessary to
read from both the DOUTA and DOUTB pins simultaneously.
Figure 30 shows both DOUTA and DOUTB of the AD7366/AD7367
connected to Serial Port 0 of the ADSP-BF53x. The SPORT0
Receive Configuration 1 register and the SPORT0 Receive
Configuration 2 register should be set up as outlined in Table 13
and Table 14.
AD7366/
AD7367*
SERIAL
DEVICE A
(PRIMARY)
ADSP-BF53x*
SPORT0
DOUTA
DR0PRI
SCLK
RCLK0
CS
The connection diagram is shown in Figure 29. The ADSP-218x
has the TFS0 and RFS0 of the SPORT0 and the RFS1 of SPORT1
tied together. TFS0 is set as an output, and both RFS0 and RFS1
are set as inputs. The DSP operates in alternate framing mode,
and the SPORT control register is set up as described in Table 11
and Table 12. The frame synchronization signal generated on
the TFS is tied to CS.
06703-031
The ADSP-218x family of DSPs interfaces directly to the
AD7366/AD7367 without any glue logic required. The VDRIVE
pin of the AD7366/AD7367 takes the same supply voltage as the
power supply pin of the ADSP-218x. This allows the ADC to
operate at a higher supply voltage than its serial interface and
therefore, the ADSP-218x, if necessary. This example shows
both DOUTA and DOUTB of the AD7366/AD7367 connected to
both serial ports of the ADSP-218x. The SPORT0 and SPORT1
control registers should be set up as shown in Table 11 and
Table 12.
RFS1
DOUTA
RFS0
BUSY
RXINTS
CNVST
PFN
DOUTB
DR0SEC
VDRIVE
SERIAL
DEVICE B
(SECONDARY)
*ADDITIONAL PINS OMITTED FOR CLARITY.
VDD
Figure 30. Interfacing the AD7366/AD7367 to the ADSP-BF53x
www.BDTIC.com/ADI/
06703-032
The serial interface on the AD7366/AD7367 allows the parts to
be directly connected to a range of different microprocessors.
This section explains how to interface the AD7366/AD7367
with some common microcontrollers and DSP serial interface
protocols.
Setting
RCKFE = 1
LRFS = 1
RFSR = 1
IRFS = 1
RLSBIT = 0
RDTYPE = 00
IRCLK = 1
RSPEN = 1
SLEN = 1111
Description
Sample data with falling edge of RSCLK
Active low frame signal
Frame every word
Internal RFS used
Receive MSB first
Zero fill
Internal receive clock
Receive enabled
16-bit data-word (or can be set to 1101 for
14-bit data-word)
TFSR = RFSR = 1
SCLK
Description
Secondary side enabled
16-bit data-word (or can be set to 1101 for
14-bit data-word)
AD7366/AD7367 TO TMS320VC5506
The serial interface on the TMS320VC5506 uses a continuous
serial clock and frame synchronization signals to synchronize
the data transfer operations with peripheral devices such as the
AD7366/AD7367. The CS input allows easy interfacing between
the TMS320VC5506 and the AD7366/AD7367 without any glue
logic required. The serial ports of the TMS320VC5506 are set
up to operate in burst mode with internal CLKX0 (Tx serial
clock on Serial Port 0) and FSX0 (Tx frame sync from Serial
Port 0). The serial port control (SPC) registers must be set up as
shown in Table 15.
CLKR0
CLKR1
DOUTA
DR0
DOUTB
DR1
CS
FO
0
0
FSM
1
1
MCM
1
0
FSX0
FSR0
FSR1
BUSY
CNVST
INTn
XF
VDRIVE
VDD
Figure 31. Interfacing the AD7366/AD7367 to the TMS320VC5506
As with the previous interfaces, conversion can be initiated
from the TMS320VC5506 or from an external source, and the
processor is interrupted when the conversion sequence is
completed.
AD7366/AD7367 TO DSP563xx
The connection diagram in Figure 32 shows how the AD7366/
AD7367 can be connected to the enhanced synchronous serial
interface (ESSI) of the DSP563xx family of DSPs from Motorola.
There are two on-board ESSIs, and each is operated in synchronous mode (Bit SYN = 1 in the CRB register) with internally
generated word length frame sync for both Tx and Rx (Bit
FSL1 = 0 and Bit FSL0 = 0 in the CRB register).
Normal operation of the ESSI is selected by setting MOD = 0 in
the CRB register. Set the word length to 16 by setting Bit WL1 = 1
and Bit WL0 = 0 in the CRA register. The FSP bit in the CRB
register should be set to 1 so that the frame sync is negative.
Table 15. Serial Port Control Register Setup
SPC
SPC0
SPC1
CLKX0
CLKX1
*ADDITIONAL PINS OMITTED FOR CLARITY.
Table 14. SPORT0 Receive Configuration 2 Register
(SPORT0_RCR2)
Setting
RXSE = 1
SLEN = 1111
TMS320VC5506*
AD7366/
AD7367*
06703-033
Table 13. SPORT0 Receive Configuration 1 Register
(SPORT0_RCR1)
TXM
1
0
The connection diagram is shown in Figure 31. The VDRIVE pin
of the AD7366/AD7367 takes the same supply voltage as the
power supply pin of the TMS320VC5506. This allows the ADC
to operate at a higher voltage than its serial interface and,
therefore, the TMS320VC5506, if necessary.
www.BDTIC.com/ADI/
In the example shown in Figure 32, the serial clock is taken
from the ESSI0, so the SCK0 pin must be set as an output
(SCKD = 1) while the SCK1 pin is set as an input (SCKD = 0).
The frame sync signal is taken from SC02 on ESSI0, so SCD2 = 1,
while on ESSI1, SCD2 = 0; therefore, SC12 is configured as an
input. The VDRIVE pin of the AD7366/AD7367 takes the same
supply voltage as the power supply pin of the DSP563xx. This
allows the ADC to operate at a higher voltage than its serial
interface and, therefore, the DSP563xx, if necessary.
DSP563xx*
AD7366/
AD7367*
SCLK
SCK0
DOUTA
SRD0
DOUTB
SRD1
CS
SC02
BUSY
IRQN
SCK1
SC12
CNVST
PBN
*ADDITIONAL PINS OMITTED FOR CLARITY.
VDD
Figure 32. Interfacing the AD7366/AD7367 to the DSP563xx
www.BDTIC.com/ADI/
06703-034
VDRIVE
APPLICATION HINTS
LAYOUT AND GROUNDING
The printed circuit board that houses the AD7366/AD7367
should be designed so that the analog and digital sections are
confined to separate areas of the board. This design facilitates the
use of ground planes that can be easily separated.
To provide optimum shielding for ground planes, a minimum
etch technique is generally the best option. All AGND pins on
the AD7366/AD7367 should be connected to the AGND plane.
Digital and analog ground pins should be joined in only one
place. If the AD7366/AD7367 are in a system where multiple
devices require an AGND and DGND connection, the connection should still be made at only one point. A star point should
be established as close as possible to the ground pins on the
AD7366/AD7367.
Good connections should be made to the power and ground
planes. This can be done with a single via or multiple vias for
each supply and ground pin.
Avoid running digital lines under the AD7366/AD7367 devices
because this couples noise onto the die. However, the analog
ground plane should be allowed to run under the AD7366/
AD7367 to avoid noise coupling. The power supply lines to
the AD7366/AD7367 should use as large a trace as possible to
provide low impedance paths and reduce the effects of glitches
on the power supply line.
To avoid radiating noise to other sections of the board, components with fast switching signals, such as clocks, should be
shielded with digital ground and should never be run near the
analog inputs. Avoid crossover of digital and analog signals. To
reduce the effects of feedthrough within the board, traces should
be run at right angles to each other. A microstrip technique is
the best method, but its use may not be possible with a doublesided board. In the microstrip technique, the component side of
the board is dedicated to ground planes, and signals are placed
on the other side.
Good decoupling is also important. All analog supplies should
be decoupled with 10 µF tantalum capacitors in parallel with
0.1 µF capacitors to AGND. To achieve the best results from
these decoupling components, they must be placed as close as
possible to the device, ideally right up against the device. The
0.1 µF capacitors should have a low effective series resistance
(ESR) and low effective series inductance (ESI), such as is typical
of common ceramic and surface mount types of capacitors. These
low ESR, low ESI capacitors provide a low impedance path to
ground at high frequencies to handle transient currents due to
internal logic switching.
www.BDTIC.com/ADI/
OUTLINE DIMENSIONS
7.90
7.80
7.70
24
13
4.50
4.40
4.30
6.40 BSC
1
12
PIN 1
0.65
BSC
0.15
0.05
0.30
0.19
1.20
MAX
SEATING
PLANE
0.20
0.09
8°
0°
0.75
0.60
0.45
0.10 COPLANARITY
COMPLIANT TO JEDEC STANDARDS MO-153-AD
Figure 33. 24-Lead Thin Shrink Small Outline Package [TSSOP]
(RU-24)
Dimensions shown in millimeters
ORDERING GUIDE
Model 1
AD7366BRUZ
AD7366BRUZ-RL7
AD7366BRUZ-500RL7
AD7367BRUZ
AD7367BRUZ-500RL7
AD7367BRUZ-RL7
EVAL-AD7366CBZ
EVAL-AD7367CBZ
EVAL-CONTROL BRD2
1
Temperature Range
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
−40°C to +85°C
Package Description
24-Lead Thin Shrink Small Outline Package [TSSOP]
24-Lead Thin Shrink Small Outline Package [TSSOP]
24-Lead Thin Shrink Small Outline Package [TSSOP]
24-Lead Thin Shrink Small Outline Package [TSSOP]
24-Lead Thin Shrink Small Outline Package [TSSOP]
24-Lead Thin Shrink Small Outline Package [TSSOP]
Evaluation Board
Evaluation Board
Control Board
Package Option
RU-24
RU-24
RU-24
RU-24
RU-24
RU-24
Z = RoHS Compliant Part.
©2007-2010 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06703-0-11/10(D)
www.BDTIC.com/ADI/
Fly UP